一、模料：
1.
1.凡长a、宽b均≥200mm钢料〈线切割模芯料后续需求淬火处理模料除外〉，统肯定购精料。
1. For all steel materials with length a and width b ≥ 200mm (except for wire cutting die core materials requiring subsequent quenching treatment), we are willing to order refined materials.
(1)精料尺寸：axbxh粗料尺寸：axbxh
(1) Fine material size: axbxh coarse material size: axbxh
(2)加硬料订购精料时单边加大0.75mm，高度加高1mm.。
(2) When adding hard materials and ordering fine materials, the single side shall be increased by 0.75mm and the height shall be increased by 1mm.
(3)行位料统一订购粗料。
(3) Coarse materials are ordered uniformly for row level materials.
(4)呵料镶件统一订购粗料，多个小镶件可拼合订购一件整料，留出适当的线割位，并做出适当的线割排位图。
(4) The coarse materials shall be uniformly ordered for material inserts, and multiple small inserts can be assembled to order a whole material, leaving appropriate line cutting position, and making appropriate line cutting arrangement diagram.
2.耐磨块遵从本质设计尺寸单边加大2mm，订购粗料。
2. The wear-resistant block shall comply with the essential design, the size shall be increased by 2mm on one side, and the coarse material shall be ordered.
3.多个直径小于Ф40mm(含)的圆材可拼合定购长件料。同时在总长度上加上车床装夹尺寸和锯床消耗尺寸15MM。单件>Ф40mm的圆材定购尺寸为设计长度加上15mm，ф110(含)下面的圆料所以5进制的，ф120(含)以上以10进制。撑头遵从本质尺寸订购，要求加工见白能够，全部圆料均订购粗料。
3. Multiple diameters less than Ф Round timber of 40mm (included) can be assembled to order long pieces. At the same time, add the lathe clamping size and sawing machine consumption size of 15mm to the total length. Single piece > Ф The order size of 40mm round timber is the design length plus 15mm, ф The round material below 110 (including) is so 5-ary, ф Above 120 (inclusive) in decimal system. The support head shall be ordered according to the essential size. It is required that the processing can be seen in white, and all round materials shall be ordered as coarse materials.
1499253774744923.jpg
1499253774744923.jpg
4.线割模料订购尺寸(a+10x(b+5)x(c+5)。
4. Order size of wire cutting die material (a + 10x (B + 5) x (c + 5).
(当中10为线切割时装夹所需尺寸，a、b辞别是零件设计尺寸。)
(among them, 10 is the required size of wire cutting fashion clip, and a and B are the design size of parts.)
5.后续需淬火处理的模料，定购尺寸(a+5)X(b+5)X(h+2)
5. For the subsequent die materials to be quenched, the order size is (a + 5) x (B + 5) x (H + 2)
(当中a、b、h为零件设计尺寸，5mm为热处理变形分量。)也可视材质来定,肯定其变形量大小适当增添尺寸,通常状况下不少于5MM.
(among them, a, B and H are the design dimensions of parts, and 5mm is the deformation component of heat treatment.) it can also be determined according to the material, confirm the deformation, and increase the size appropriately, usually not less than 5mm
6.斜顶订购方式同于线割模料订购尺寸，假如一套模中的斜顶较多，可将尺寸和形式相近的斜顶订购在一块料上，并适当排位，便于线割加工。
6. The inclined top ordering method is the same as the wire cutting die material ordering size. If there are many inclined tops in a set of dies, the inclined tops with similar size and form can be ordered on one piece of material and properly arranged for wire cutting processing.
二、模架
Two. Mould frame
1、模架遵从龙记准则订购，假如客户有指定，遵从客户指定订购。
1. The mold base shall be ordered in accordance with Longji guidelines. If the customer has specified, the order shall be in accordance with the customer's specified order.
2、模架开框尺寸：X、Y在300下面的衙役为，X、Y在301以上的衙役为。深度衙役通常遵从龙记准则做，50以上的开框深度衙役为。
2. The opening dimension of formwork: for the Yamen with X and y below 300, and for the Yamen with X and Y above 301. The depth yamen usually follow the Longji standard, and the opening depth Yamen with X and Y above 50 is.
3、模胚开框图内要注明技艺要求及个体相关方式。
3. The technical requirements and individual related methods shall be indicated in the mold opening block diagram.
三、模具配件
Three, mold accessories
1、凡选用DME和HASCO及大同准则顶针和司筒时，除在订料单上注明其型号外另以复印方式将所指定的顶针或司筒地点页码复印走出，并以打勾方式注明，作为附页一起下发，并在BOM单上注明是DME(欧洲或北美)或HASCO(欧洲)规格。
1. When DME, HASCO and Datong standard thimble and cylinder are selected, in addition to indicating the model on the purchase order, the page number of the designated thimble or cylinder location shall be copied out in the form of copy, marked in the form of tick, distributed as an attached page, and indicated as DME (Europe or North America) or HASCO (Europe) specification on the BOM.
2、当用到非标司筒时，在订料上注明非标外，还要注明非标字样，并以附图方式打印并下发。
2. When non-standard cylinders are used, non-standard words shall be indicated on the ordering materials in addition to non-standard words, which shall be printed and distributed in the form of drawings.
3、弹弓注明供应商，并写明颜色(通常状况下选用蓝弹弓较多);水口拉针要注明型号和供应商;唧嘴多由本厂加工，只需订购圆料和写明尺寸并附图，不需注明供应商。
3. The slingshot shall be marked with the supplier and the color (usually blue Slingshot is more used); the model and supplier of the nozzle pull needle shall be marked; the pump nozzle is mostly processed by our factory, so it is only necessary to order round materials, indicate the size and attach drawings, without indicating the supplier.
